# recommendations for processing with poor quality forward reads

**URL:** <https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243>\
**Category:** User Support\
**Tags:** dada2\
**Created:** [July 19, 2021, 6:28pm UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243 "2021-07-19T18:28:49Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![anna-schrecengost](https://forum.qiime2.org/user_avatar/forum.qiime2.org/anna-schrecengost/32/10398_2.png) [@anna-schrecengost](https://forum.qiime2.org/u/anna-schrecengost)\
**Post date:** [July 19, 2021, 6:28pm UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243/1 "2021-07-19T18:28:50Z")

</div>

Hi, I am analyzing some 16S V4 rRNA amplicon data from low-diversity symbiont communities, planning on using DADA2 in QIIME2. The issue I am having is that the quality of the forward reads is very poor, while the quality of the reverse reads is also bad but more usable and typical for reverse reads I think. Example sequencing run:

 ![image](https://forum-qiime2-org.s3.dualstack.us-west-2.amazonaws.com/original/2X/c/c41693e6fcdedd6341edef69fce05683ef683dd1.jpeg)  
[demux-paired-end.qzv](https://forum.qiime2.org/uploads/short-url/mXarAgURcA9mw2YNkklV4WoRlgb.qzv) (311.6 KB)

(the primer set results in an amplicon of ~400 bp, and the sequencing chemistry was 2x250 bp, so I'd expect ~100 bp overlap)

I'm not sure that DADA2 will be able to merge these, although I will attempt to run it in paired end mode and play with the parameters. But I suspect the forward reads might be too low quality to use at all, and I might want to denoise only the reverse reads. Is this possible in DADA2? I know that you can use only forward reads in the single end mode, but haven't found any info about using only reverse reads. I would appreciate any insight, thank you!

---

<div class="post-metadata">

**Author:** ![lizgehret](https://forum.qiime2.org/user_avatar/forum.qiime2.org/lizgehret/32/17128_2.png) [@lizgehret](https://forum.qiime2.org/u/lizgehret)\
**Post date:** [July 22, 2021, 6:30pm UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243/2 "2021-07-22T18:30:43Z")

</div>



---

<div class="post-metadata">

**Author:** ![lizgehret](https://forum.qiime2.org/user_avatar/forum.qiime2.org/lizgehret/32/17128_2.png) [@lizgehret](https://forum.qiime2.org/u/lizgehret)\
**Post date:** [July 22, 2021, 6:53pm UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243/3 "2021-07-22T18:53:47Z")

</div>

Hi @anna-schrecengost,

Thanks for reaching out and for providing those sequencing run screenshots! Here are a few thoughts on how to proceed here:

As of the QIIME 2 2021.4 release, DADA2 requires at least 12nt overlap for proper merging - so that's something to keep in mind if you only have ~100 bp of overlap.

I do agree with you that your forward reads are pretty low in quality, and may not be good enough to use at all (it appears as though the only semi-decent quality score is from 0-10 in your sequence base, which is pretty short).

Using only reverse reads in `denoise-single` isn't typically recommended due to the commonly lower quality scores of reverse reads, but in this case it does seem like your best bet. In [this forum post](https://forum.qiime2.org/t/p-trim-and-p-trunc-values-selection-for-qiime-dada2-denoise-paired/9840/4), this is what @Mehrbod_Estaki recommended to another user who has poor quality forward reads as well. Hopefully this helps!

Cheers,  
Liz

---

<div class="post-metadata">

**Author:** ![lizgehret](https://forum.qiime2.org/user_avatar/forum.qiime2.org/lizgehret/32/17128_2.png) [@lizgehret](https://forum.qiime2.org/u/lizgehret)\
**Post date:** [July 22, 2021, 6:53pm UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243/4 "2021-07-22T18:53:59Z")

</div>



---

<div class="post-metadata">

**Author:** ![anna-schrecengost](https://forum.qiime2.org/user_avatar/forum.qiime2.org/anna-schrecengost/32/10398_2.png) [@anna-schrecengost](https://forum.qiime2.org/u/anna-schrecengost)\
**Post date:** [July 22, 2021, 7:10pm UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243/6 "2021-07-22T19:10:49Z")

</div>

Thank you @lizgehret!

---

<div class="post-metadata">

**Author:** ![system](https://forum-qiime2-org.s3.dualstack.us-west-2.amazonaws.com/original/3X/2/1/21af5fe23cb6f4579467c66a9ed94e55274ca7bd.svg) [@system](https://forum.qiime2.org/u/system)\
**Post date:** [August 23, 2021, 1:13am UTC](https://forum.qiime2.org/t/recommendations-for-processing-with-poor-quality-forward-reads/20243/8 "2021-08-23T01:13:51Z")

</div>

This topic was automatically closed 31 days after the last reply. New replies are no longer allowed.
